Hawk Performance

Hawk Performance HT-10 Rear Brake Pads - HB485S.656

$212.39

~~$235.99~~ $212.39

Sale

Quantity

Hawk Performance HT-10

For linear in-braking in a medium temperature range, look no further than HT-10. It delivers smooth, controllable initial bite and consistent pedal feel. It's no wonder Hawk's legacy friction products have become the choice of champions.

Hawk Performance HT-10 Race Compound Characteristics:

Good Static and Dynamic Coefficient of Friction
Excellent modulation characteristics
300-1300 Deg F Operating Temperature Range
300-1100 Deg F Optimal Temperature Range

Hawk Race Compound Chart

Hawk Brake Pad Installation Procedure

Install Brake pads properly. Be sure pads are securely positioned in the caliper.
Flush system with fresh brake fluid.
Check all hydraulic parts for excess wear and tear.
Check disc for proper thickness, parallelism, and lateral run-out.
Check disc for scoring or grooves over .012"" depth. If either applies, resurfacing or replacement is required.
If disc does not need resurfacing then contamination from the previous brake pads must be removed. Sand discs with Garnet sandpaper using moderate pressure. Use soap and water to clean off disc surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid
Inspect calipers for freedom of movement. Lubricate where necessary

Hawk Brake Pad Bedding Procedure - Motorsports Pads

After reaching medium speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat four or five times.
At higher speeds engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat five times.
At or near race speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat three times. Allow a few seconds between brake engagements while car is in motion.
Do not hold brake pedal. Park car for approximately 20 minutes or until brake rotors are completely cool to the touch.
If during the above steps the brake pedal becomes soft or brake fade is noticed, park the car immediately for approximately 20 minutes. Do not hold brake pedal.

Important Reminders when Burnishing or Bedding Brake Pads

Do not attempt to use badly worn or damaged rotors with new brake pads.
Do not drag brakes while car is moving during break-in procedure.
Do not engage pedal while car is stopped at any time following the break-in procedure.
Upon completing the procedure, allow the brake system to completely cool before racing.
Applying the pedal a few times before the start of the race will allow the brake pads to heat up before attempting to reach race speeds.
Some forms of racing do not allow time for the proper break-in procedure to be performed. However, it is still very important to attempt to perform at least the core of the procedure: Build up heat slowly and allow the system to completely cool down before racing if possible.

This part is for the Rear of:

2014 Ford Mustang Shelby GT500 5.8L
2014 Ford Mustang GT Automatic Trans 5.0L
2014 Ford Mustang GT 5.0L Exc.Brembo Package
2014 Ford Mustang Base Manual Trans 3.7L
2014 Ford Mustang Base Automatic Trans 3.7L Performance Package
2014 Ford Mustang Base 3.7L Exc.Performance Package
2013 Ford Mustang Shelby GT500 To 12/21/2012 5.8L
2013 Ford Mustang Shelby GT500 From 12/22/2012 5.8L
2013 Ford Mustang GT To 12/21/2013 5.0L Exc.Brembo Brakes
2013 Ford Mustang GT From 12/22/2012 5.0L Exc.Brembo Brakes
2013 Ford Mustang Boss 302 To 12/21/2012 5.0L
2013 Ford Mustang Boss 302 From 12/22/2012 5.0L
2013 Ford Mustang Base To 12/21/2012 3.7L Exc.Performance Package
2013 Ford Mustang Base Manual Trans, To 12/21/2012 3.7L Performance Package
2013 Ford Mustang Base Manual Trans, From 12/22/2012 3.7L Performance Package
2013 Ford Mustang Base From 12/22/2012 3.7L Exc.Performance Package
2013 Ford Mustang Base Automatic Trans, To 12/21/2012 3.7L Performance Package
2013 Ford Mustang Base Automatic Trans, From 12/22/2012 3.7L Performance Package
2012 Ford Mustang GT From 07/21/2011 5.0L Exc.Brembo Brakes
2012 Ford Mustang Boss 302 To 07/21/2011 5.0L
2012 Ford Mustang Boss 302 From 07/21/2011 5.0L
2012 Ford Mustang Base To 07/21/2011 3.7L Performance Package
2012 Ford Mustang Base To 07/21/2011 3.7L Exc.Performance Package
2012 Ford Mustang Base From 07/21/2011 3.7L Performance Package
2012 Ford Mustang Base From 07/21/2011 3.7L Exc.Performance Package
2011 Ford Mustang Shelby GT500 5.4L
2011 Ford Mustang GT 5.0L
2011 Ford Mustang Base 3.7L Performance Package
2011 Ford Mustang Base 3.7L Exc.Performance Package
2010 Ford Mustang Shelby GT500 5.4L OE Incl.Clips
2010 Ford Mustang GT 4.6L Exc.Brembo package
2010 Ford Mustang GT 4.6L
2010 Ford Mustang Base 4.0L
2010 Ford Mustang
2009 Ford Mustang Shelby GT500KR 5.4L
2009 Ford Mustang Shelby GT500 5.4L OE Incl.Clips
2009 Ford Mustang GT 4.6L
2009 Ford Mustang Bullitt 4.6L
2009 Ford Mustang 4.0L
2008 Ford Mustang Shelby GT500KR 5.4L
2008 Ford Mustang Shelby GT500 5.4L OE Incl.Clips
2008 Ford Mustang Shelby GT 4.6L
2008 Ford Mustang GT 4.6L
2008 Ford Mustang Bullitt 4.6L OE Incl.Clips
2008 Ford Mustang 4.0L
2007 Ford Mustang Shelby GT500 5.4L OE Incl.Clips
2007 Ford Mustang Shelby GT 4.6L
2007 Ford Mustang GT 4.6L
2007 Ford Mustang 4.0L
2006 Ford Mustang GT 4.6L
2006 Ford Mustang 4.0L
2005 Ford Mustang GT 4.6L
2005 Ford Mustang 4.0L