Hawk Brake Pad Installation Procedure

• Install Brake pads properly. Be sure pads are securely positioned in the caliper.
• Flush system with fresh brake fluid.
• Check all hydraulic parts for excess wear and tear.
• Check disc for proper thickness, parallelism, and lateral run-out.
• Check disc for scoring or grooves over .012"" depth. If either applies, resurfacing or replacement is required.
• If disc does not need resurfacing then contamination from the previous brake pads must be removed. Sand discs with Garnet sandpaper using moderate pressure. Use soap and water to clean off disc surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid
• Inspect calipers for freedom of movement. Lubricate where necessary

Hawk Brake Pad Bedding Procedure - Motorsports Pads

• After reaching medium speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat four or five times.
• At higher speeds engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat five times.
• At or near race speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat three times. Allow a few seconds between brake engagements while car is in motion.
• Do not hold brake pedal. Park car for approximately 20 minutes or until brake rotors are completely cool to the touch.
• If during the above steps the brake pedal becomes soft or brake fade is noticed, park the car immediately for approximately 20 minutes. Do not hold brake pedal.

Important Reminders when Burnishing or Bedding Brake Pads

• Do not attempt to use badly worn or damaged rotors with new brake pads.
• Do not drag brakes while car is moving during break-in procedure.
• Do not engage pedal while car is stopped at any time following the break-in procedure.
• Upon completing the procedure, allow the brake system to completely cool before racing.
• Applying the pedal a few times before the start of the race will allow the brake pads to heat up before attempting to reach race speeds.
• Clean a used rotor surface with fine sand paper or steel wool, rinse with water, dry and install before bedding new pads.
• Some forms of racing do not allow time for the proper break-in procedure to be performed. However, it is still very important to attempt to perform at least the core of the procedure: Build up heat slowly and allow the system to completely cool down before racing if possible.

This part is for the Front of:

• 2002 BMW Z3 3.2L
• 2001 BMW Z3 3.2L
• 2000 BMW Z3 3.2L
• 1999 BMW Z3 3.2L
• 1999 BMW M3 3.2L
• 1998 BMW Z3 3.2L
• 1998 BMW M3 3.2L
• 1998 BMW 528i 2.8L
• 1997 BMW M3 3.2L
• 1997 BMW 528i 2.8L
• 1996 BMW M3 3.2L
• 1995 BMW M3 3.0L
• 1995 BMW 540i 4.0L
• 1995 BMW 530i 3.0L
• 1995 BMW 525iT
• 1995 BMW 525i 2.5L
• 1995 BMW 525i
• 1994 BMW 750iL 5.0L
• 1994 BMW 740iL 4.0L
• 1994 BMW 740i 4.0L
• 1994 BMW 540i 4.0L
• 1994 BMW 530i 3.0L
• 1994 BMW 525iT
• 1994 BMW 525i 2.5L
• 1993 BMW M5 3.6L
• 1993 BMW 750iL 5.0L
• 1993 BMW 740iL 4.0L
• 1993 BMW 740i 4.0L
• 1993 BMW 535i 3.5L
• 1993 BMW 525iT
• 1993 BMW 525i 2.5L
• 1992 BMW M5 3.6L
• 1992 BMW 750iL 5.0L
• 1992 BMW 735iL 3.5L
• 1992 BMW 735i 3.5L
• 1992 BMW 535i 3.5L
• 1992 BMW 525i 2.5L
• 1991 BMW M5 3.6L
• 1991 BMW 750iL 5.0L
• 1991 BMW 735iL 3.5L
• 1991 BMW 735i 3.5L
• 1991 BMW 535i 3.5L
• 1991 BMW 525i 2.5L
• 1991 Audi Coupe Quattro 20v 2.3L
• 1991 Audi 200 Quattro 20v 2.2L 1 Piston Caliper
• 1991 Audi 200 Base 2.3L
• 1991 Audi 200 Base 2.2L 1 Piston Caliper
• 1990 BMW 750iL 5.0L
• 1990 BMW 735iL 3.5L
• 1990 BMW 735i 3.5L
• 1990 BMW 535i 3.5L
• 1990 BMW 525i 2.5L
• 1990 Audi 200 Quattro Base 2.2L 1 Piston Caliper
• 1990 Audi 200 Base 2.2L 1 Piston Caliper
• 1989 BMW 750iL 5.0L
• 1989 BMW 735iL 3.5L
• 1989 BMW 735i 3.5L
• 1989 BMW 535i 3.5L
• 1989 BMW 525i 2.5L
• 1989 Audi 200 Quattro Base 2.2L
• 1989 Audi 200 Base 2.2L 1 Piston Caliper
• 1989 Audi 100 Quattro Base 2.2L 1 Piston Caliper
• 1988 BMW 750iL 5.0L
• 1988 BMW 735iL 3.5L
• 1988 BMW 735i 3.5L
• 1988 BMW 535is 3.5L
• 1988 BMW 535i 3.5L
• 1987 BMW 735i 3.5L