Hawk .650 HT-10 Rear Brake Pads For 97-13 Chevrolet Corvette - HB248S.650

Hawk Performance HT-10

For linear in-braking in a medium temperature range, look no further than HT-10. It delivers smooth, controllable initial bite and consistent pedal feel. It's no wonder Hawk's legacy friction products have become the choice of champions.

Hawk Performance HT-10 Race Compound Characteristics:

• Good Static and Dynamic Coefficient of Friction
• Excellent modulation characteristics
• 300-1300 Deg F Operating Temperature Range
• 300-1100 Deg F Optimal Temperature Range

Hawk Race Compound Chart

Hawk Brake Pad Installation Procedure

• Install Brake pads properly. Be sure pads are securely positioned in the caliper.
• Flush system with fresh brake fluid.
• Check all hydraulic parts for excess wear and tear.
• Check disc for proper thickness, parallelism, and lateral run-out.
• Check disc for scoring or grooves over .012"" depth. If either applies, resurfacing or replacement is required.
• If disc does not need resurfacing then contamination from the previous brake pads must be removed. Sand discs with Garnet sandpaper using moderate pressure. Use soap and water to clean off disc surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid
• Inspect calipers for freedom of movement. Lubricate where necessary

Hawk Brake Pad Bedding Procedure - Motorsports Pads

• After reaching medium speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat four or five times.
• At higher speeds engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat five times.
• At or near race speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat three times. Allow a few seconds between brake engagements while car is in motion.
• Do not hold brake pedal. Park car for approximately 20 minutes or until brake rotors are completely cool to the touch.
• If during the above steps the brake pedal becomes soft or brake fade is noticed, park the car immediately for approximately 20 minutes. Do not hold brake pedal.

Important Reminders when Burnishing or Bedding Brake Pads

• Do not attempt to use badly worn or damaged rotors with new brake pads.
• Do not drag brakes while car is moving during break-in procedure.
• Do not engage pedal while car is stopped at any time following the break-in procedure.
• Upon completing the procedure, allow the brake system to completely cool before racing.
• Applying the pedal a few times before the start of the race will allow the brake pads to heat up before attempting to reach race speeds.
li>Clean a used rotor surface with fine sand paper or steel wool, rinse with water, dry and install before bedding new pads
• Some forms of racing do not allow time for the proper break-in procedure to be performed. However, it is still very important to attempt to perform at least the core of the procedure: Build up heat slowly and allow the system to completely cool down before racing if possible.

This part is for the Rear of:

• 2013 Chevrolet Corvette Base 6.2L Heavy Duty Brakes, OE Incl.Clips
• 2013 Chevrolet Corvette Base 6.2L Exc.Heavy Duty Brakes, OE Incl.Clips
• 2012 Chevrolet Corvette Base 6.2L Heavy Duty Brakes, OE Incl.Clips
• 2012 Chevrolet Corvette Base 6.2L Exc.Heavy Duty Brakes, OE Incl.Clips
• 2011 Chevrolet Corvette Base 6.2L Heavy Duty Brakes, OE Incl.Clips
• 2011 Chevrolet Corvette Base 6.2L Exc.Heavy Duty Brakes, OE Incl.Clips
• 2010 Chevrolet Corvette Base 6.2L Heavy Duty Brakes, OE Incl.Clips
• 2010 Chevrolet Corvette Base 6.2L Exc.Heavy Duty Brakes, OE Incl.Clips
• 2009 Chevrolet Corvette Base 6.2L Heavy Duty Brakes, OE Incl.Clips
• 2009 Chevrolet Corvette Base 6.2L Exc.Heavy Duty Brakes, OE Incl.Clips
• 2008 Chevrolet Corvette Base 6.2L Heavy Duty Brakes, OE Incl.Clips
• 2008 Chevrolet Corvette Base 6.2L Exc.Heavy Duty Brakes, OE Incl.Clips
• 2007 Chevrolet Corvette Base 6.0L Heavy Duty Brakes, OE Incl.Clips
• 2007 Chevrolet Corvette Base 6.0L Exc.Heavy Duty Brakes, OE Incl.Clips
• 2006 Chevrolet Corvette Base 6.0L Heavy Duty Brakes, OE Incl.Clips
• 2006 Chevrolet Corvette Base 6.0L Exc.Heavy Duty Brakes, OE Incl.Clips
• 2005 Chevrolet Corvette Base 6.0L Heavy Duty Brakes, OE Incl.Clips
• 2005 Chevrolet Corvette Base 6.0L Exc.Heavy Duty Brakes, OE Incl.Clips
• 2004 Chevrolet Corvette Z06 5.7L
• 2004 Chevrolet Corvette Base 5.7L
• 2003 Chevrolet Corvette Z06 5.7L
• 2003 Chevrolet Corvette Base 5.7L
• 2003 Chevrolet Corvette 50th Anniversary Edition Pace Car 5.7L
• 2003 Chevrolet Corvette 50th Anniversary Edition 5.7L
• 2003 Chevrolet CORVETTE
• 2002 Chevrolet Corvette Z06 5.7L
• 2002 Chevrolet Corvette Base 5.7L
• 2002 Chevrolet CORVETTE
• 2001 Chevrolet Corvette Z06 5.7L
• 2001 Chevrolet Corvette Base 5.7L
• 2001 Chevrolet CORVETTE
• 2000 Chevrolet Corvette Base 5.7L
• 2000 Chevrolet CORVETTE
• 1999 Chevrolet Corvette Base 5.7L
• 1999 Chevrolet CORVETTE
• 1998 Chevrolet Corvette Indianapolis 500 Pace Car 5.7L
• 1998 Chevrolet Corvette Base 5.7L
• 1998 Chevrolet CORVETTE
• 1997 Chevrolet Corvette Base 5.7L
• 1997 Chevrolet CORVETTE